1 ).	How to Change the Default Folder Locations for Virtual Hard Disk Image Files
	This article discusses how to change the default storage location for Virtual PC virtual hard disk image files (.vhd), for guest PC saved state files (.vsv), and for undo drive files (.vud). By default, when you create a new guest PC, these image files...
2 ).	How to install Virtual PC Additions on a guest PC
	This article describes how to install Virtual PC Additions on a guest PC in Virtual PC.
3 ).	Additional Guest PC COM Ports Do Not Work After You Add Them
	After you create an additional COM port in the guest PC settings, that COM port does not work when you start the guest PC.
4 ).	"One or More Files Missing" Error Message When You Try to Start Virtual PC
	After you install Virtual PC, when you try to start Virtual PC, you receive the following error message: You cannot start Virtual PC.
5 ).	Windows Stops Responding After You Install Virtual PC
	After you install or upgrade to Virtual PC 5.x, Windows stops responding. The Virtual PC.exe process may cause 99 to 100 percent CPU utilization.
6 ).	How to Install, to Configure, and to Remove the Virtual PC Emulated Ethernet Switch for Windows NT 4.0
	This step-by-step article describes how to install, to configure, and to remove the Virtual PC Emulated Ethernet Switch for Windows NT 4.0. The Virtual PC Emulated Ethernet Switch for Windows NT 4.0 driver (VPCNetNT.sys) is a network driver interface...
7 ).	How to Install DOS Additions for Additional Functionality in a DOS-Based Guest PC
	This step-by-step article describes how to install Virtual PC DOS Additions for additional functionalities such as Shared Folders in a DOS-based guest PC operating system.
8 ).	Poor Performance When You Use IBM OS/2 Warp As a Guest Operating System
	When you install IBM OS/2 Warp as a guest operating system in Virtual PC, you may find that the performance of the guest PC is poor.
9 ).	Virtual PC for Windows 5.0 and later does not run on computers that use a Transmeta Crusoe microprocessor or an AMD K6 CPU
	When you try to run Virtual PC for Windows version 5.0 or later on a computer that uses a Transmeta Crusoe microprocessor or an Advanced Micro Devices (AMD) K6 CPU, you cannot do so. The Virtual PC program does not start.
10 ).	Novell NetWare 5.1 installation stops responding on a computer that uses a Pentium 4 processor
	When you try to install Novell Netware 5.1 on a Connectix Virtual PC guest PC, the installation may not be completed successfully. The installation program may stop responding. Note If you switch to Console view after the installation program stops...
11 ).	How to create a Windows 98 emergency boot disk from PC DOS 2000
	This article discusses how to create a Microsoft Windows 98 Emergency Boot Disk (EBD) from IBM PC DOS 2000.
12 ).	How to Create Virtual Machine Shortcuts in Virtual PC
	This step-by-step article describes how to create shortcuts to virtual machines that you have created in Virtual PC. You can start a particular virtual machine by using a shortcut. You can also use these shortcuts to start virtual machines with various...
13 ).	Preinstalled Print Drivers in Connectix OS Pack with Windows 98 Do Not Work
	The print drivers that are preinstalled in the Connectix OS Pack with Windows 98 do not work in Virtual PC for Windows
14 ).	Mouse Pointer Disappears or Changes to a Square in a Guest PC
	When you start a guest PC, the pointer may disappear or may change to a square in the guest PC. This problem may occur when either of the following conditions is true: The Enable pointer shadow check box is selected.The guest PC is accessed...
15 ).	How to configure memory for a PC-DOS 2000 guest operating system
	This article describes how to configure memory for a PC DOS 2000 guest operating system.

[ 1 ] 2 3 4 5

Page 1 of 5 Next Page

PC Fixer

Fix a wide variety of PC problems for Free!